Ergonomics

Shop ergonomic solutions built to reduce fatigue, improve comfort, and support better movement on the job. Ideal for warehouses, workstations, and industrial settings, these products help workers stay productive, comfortable, and focused throughout long shifts.

Ergonomics buying guide
Ergonomics

For trades that spend the day down on hard floors, gel knee pads cushion the pressure points that cause the damage.

Crews doing repetitive lifting are better served by a back support belt with lumbar padding.

Flooring and concrete crews most often choose the GR553 heavy-duty knee pads for their non-slip TPE cap.

Kitting out a distribution centre? See the full spec in PPE for warehousing.

Quick guide

Ergonomic PPE: knee pads and back support belts

This collection covers the two strains that build up over long shifts: kneeling and lifting. Three knee pads certified to EN 14404 cushion the knees on hard, rough and finished floors, and two lumbar back support belts remind workers to lift straight. Use the guide below to match each product to the surface, the task and the work area.

Key takeaways

  • Knee pads by surface. PVC cap for rough ground, TPE cap for smooth floors, slim EVA foam for finished floors and crawl spaces.
  • Gel for long kneeling. The GR551 and GR553 add a gel core over EVA foam to spread pressure on hard floors.
  • Belts support technique, not strength. A back belt encourages a straighter lift; it does not remove the risk of a lifting injury.
  • OSHA does not require back belts. They sit alongside lift training, load limits and mechanical aids, not in place of them.
  • Hi-vis where vehicles move. The GR542 belt is lime for docks, yards and forklift zones; the GR540 is black for indoor work.

Standards that apply

EN 14404
Knee protectors for work in the kneeling position, by attachment type and by penetration resistance: Level 0 for flat floors, Level 1 for at least 100 N, Level 2 for at least 250 N.
OSHA 29 CFR 1910.132
Employers must assess workplace hazards, certify the assessment in writing, select PPE and train workers.
Back support belts
No safety standard rating is published for our belts, and OSHA does not require back belts.

Compare the ergonomic range

ProductTypeStandardBuildFitBest for
GR550 · Low-profile EVA foamKnee pad, sold per padEN 14404Medium-density EVA foam, soft cover, no capNeoprene straps, hook-and-loopIndoors, flooring, tight spaces
GR551 · Pro, PVC capKnee padEN 14404EVA foam with gel core, thick PVC capNeoprene straps, quick-release slide clipRough, abrasive and outdoor surfaces
GR553 · Heavy-duty gelKnee padEN 14404Contoured EVA and gel foam, TPE grip capAdjustable neoprene strapsConcrete, tile, smooth floors
GR540 · Lumbar back support beltBack belt, black—8" back panel, 4.5" elastic side bands, adjustable suspendersBy waist measurementIndoor lifting, stockrooms, assembly
GR542 · Hi-vis back support beltBack belt, hi-vis lime—8" back panel, elastic side bands, adjustable suspendersBy waist measurementDocks, yards, forklift zones

From each product's specification sheet and our PPE Materials guide. “—” means no standard rating is published. Compare in more detail in knee pads and back support belts.

What it is made of

EVA foam and gel

EVA foam is light and cushions; a gel core spreads pressure on hard floors. All three knee pads use EVA, two add gel.

PVC and TPE caps

A hard PVC cap lets you pivot and keeps debris out; a soft TPE cap grips smooth floors without marking them.

Lumbar panel and suspenders

An 8" wide heavy-duty back panel with elastic side bands, held in place by adjustable suspenders when the belt is loosened between lifts.

Which product for which job

Manufacturing

Back support belts for lifting stations and knee pads for maintenance and floor-level work: GR540, GR550.

Warehousing

Lumbar support for repetitive lifting and knee pads for low-shelf picking and racking work.

Construction

Knee pads for flooring and finishing crews, such as the GR553 on concrete and tile.

Ergonomic PPE helps workers manage the strain that builds up over long shifts, from hours of kneeling to repeated lifting. This collection has three knee pads certified to EN 14404, in EVA foam or gel with PVC or TPE caps, and two lumbar back support belts, one black and one hi-vis. Below: how to choose knee pads by surface, what back belts honestly do, how to fit both, and how to buy for a crew.

Two strains, two different products

Kneeling and lifting damage the body slowly. Knee damage is cumulative and rarely announces itself the way a cut does, so it drops down the priority list. Lifting strain builds the same way, one box at a time.

Knee pads put a cushion and a cap between the knee and the floor. Back support belts do something different: they remind the wearer to lift with a straight spine. Neither replaces the controls that come first, such as mechanical lift aids, load limits and lift training. Start with the written hazard assessment OSHA 29 CFR 1910.132 requires, then choose the PPE.

Knee pads

What EN 14404 covers

EN 14404 is the European standard for knee protectors used in the kneeling position. It sorts them by how they attach and by performance level: Level 0 for flat floors with no penetration resistance, Level 1 for at least 100 N of penetration resistance and Level 2 for at least 250 N, for rough or debris-covered ground. All three of our knee pads are certified to EN 14404.

Foam, gel or cap: choose by the surface

The GR550 low-profile knee pad uses medium-density EVA foam with a soft cover and no cap. It is slim enough to wear over or under work pants, which suits finished floors and tight crawl spaces. It is sold as one pad per card, so order two per worker.

The GR551 pro knee pads add a gel core and a thick PVC cap. The hard cap lets a worker pivot, keeps stones and debris out and takes the wear of rough, abrasive ground.

The GR553 heavy-duty gel knee pads combine contoured EVA and gel foam with a TPE cap. TPE grips smooth floors without marking them, so the pad stays where you kneel on concrete, tile and hardwood.

Straps keep pads in place

Most complaints about knee pads are strap complaints: pads slip down, cut off circulation or come off at lunch and stay off. All three of ours use neoprene straps; the GR551 closes with a quick-release slide clip. Fasten them snug enough that the pad stays over the kneecap without restricting circulation.

Back support belts

What a belt does, honestly

Back belts do not make a worker stronger and they do not remove the risk of a lifting injury. What they do is give positional feedback: the belt reminds the wearer where their spine is, which encourages a straighter lift and discourages twisting under load. OSHA does not require back belts and does not treat them as a substitute for engineering controls. Read more in our guide to back support belts at work.

Fit and use

Both of our belts have an 8" wide heavy-duty back panel, elastic side bands and adjustable suspenders. Choose the size by waist measurement, center the panel on the lower back and pull the side bands forward to snug the belt for the lift. Loosen them between lifts so the belt does not restrict breathing or movement; the suspenders keep a loosened belt from sliding down.

The black GR540 suits indoor work. The GR542 hi-vis belt is lime for workers who lift near forklifts, trucks or traffic.

Ergonomics by industry

In manufacturing, back support belts sit at lifting stations and knee pads cover maintenance and floor-level work.

In warehousing and distribution, lumbar support helps with repetitive lifting and knee pads protect pickers on low shelves and during racking work.

In transportation and logistics, crews lift at docks and in trailers and kneel for loading work, which is where the hi-vis belt and a capped knee pad earn their place.

On construction sites, flooring and finishing crews need knee pads matched to concrete, tile or rough ground.

Buying ergonomic PPE for a crew

Issue belts and knee pads per person rather than as shared stock: each worker needs the right size, and shared belts and pads raise hygiene problems. Replace knee pads when the foam compresses flat or a strap fails, and belts when the elastic loses its recovery or the hook and loop stops holding. Send us your headcount and tasks and we will quote case pricing, or apply as a distributor.

Frequently Asked Questions

Which knee pads are best for concrete?

A gel pad with a cap. The GR553 has a TPE cap that grips smooth concrete and tile; the GR551 has a hard PVC cap for rough or debris-covered ground.

Are gel or foam knee pads better?

Gel spreads load better and stays comfortable longer, so it suits long stretches in one position. Foam is lighter and slimmer and handles general work and tight spaces well.

Do back support belts prevent back injuries?

No belt prevents injury on its own. A belt gives positional feedback that encourages a straighter lift, but it does not make anyone stronger and does not replace lift training, load limits or mechanical aids.

Does OSHA require back belts or knee pads?

OSHA does not require back belts. For all PPE, 29 CFR 1910.132 requires a written hazard assessment, and knee protection is selected from it where workers kneel.

What does EN 14404 mean on a knee pad?

It is the European standard for knee protectors used in the kneeling position. It classifies pads by how they attach and by penetration resistance, from Level 0 for flat floors to Level 2 for at least 250 N on rough ground.

Should a back belt be worn tight all day?

No. Wear it loose while moving and tighten it for the lift. A belt worn tight all shift gets taken off and left off.

Related guides